🌐 Translate
Automatic translation is available via Google Translate: Open translated version.

Radio operation

This page covers the day-to-day operation of the transceiver: switching between VFO and memory mode, reading the status bar, understanding TX restrictions, and managing sleep behavior.

For scan-related features, see Scanning. For browser-based live viewing and maintenance, see UV Studio. For radio-to-radio copying, see AirCopy. For RescueOps, Resume Mode, the built-in game, and the research-oriented TX unlock procedure, see Advanced features.

[!WARNING] Do not use Quansheng CPS. It overwrites custom settings.

On this page

[!TIP] Common quick checks:

See Troubleshooting for the short version.

Basic operation & configuration

The radio display is split into an upper VFO and a lower VFO. You can change upper/lower selection by pressing F + 2 A/B (or by long-pressing 2 A/B).

Each VFO can operate independently in either frequency mode or channel mode. To switch modes, select the desired VFO and press F + 3 VFO/MR (or long-press 3 VFO/MR).

DW

In frequency mode, you manually enter the frequency with the keypad. You can also change different options for that VFO in the menu (the first 13 menu entries). Once the VFO is set up, the settings can be saved to a memory channel by going into the ChSave menu and choosing the target memory channel.

In channel mode, you can switch between saved memory channels. Memory channels can be added manually as mentioned above or programmed from a computer with the CHIRP driver provided with each firmware release. See Programming with CHIRP for the dedicated F4HWN workflow.

For frequency scan, memory scan, ScnRng, and DCS / CTCSS scanning, see Scanning.

Status bar

At the top of the screen, on the first line, is the status bar. It displays a lot of information. Here are some examples:

Screenshot of the Quansheng K5 running the F4HWN firmware Description
1 DWR means RxMode is set to DUAL RX RESPOND, OP means PTT is set to ONEPUSH, the F icon means the F key has been pressed, and you see the battery voltage.
2 PS means Power Save is activated, DW means RxMode is set to MAIN TX / DUAL RX, VX means VOX is activated, CL means PTT is set to CLASSIC, the lock icon means the keypad is locked, and you see the battery voltage.
3 PS means Power Save is activated, MO means RxMode is set to MAIN ONLY, OP means PTT is set to ONEPUSH, and you see the battery percentage.
4 MO means RxMode is set to MAIN ONLY, OP means PTT is set to ONEPUSH, the Light icon means the manual Backlight control is activated, and you see the battery percentage.
5 The RX timer on the left indicates how long it has been since you received a signal, OP means PTT is set to ONEPUSH, the Light icon means the manual Backlight control is activated and you see the battery percentage.
6 The small PMR in reverse video and >< mean you are currently scanning list PMR, CL means PTT is set to CLASSIC, the Light icon means the manual Backlight control is activated, and you see the battery percentage.
7 The ALL icon and >< mean you are currently scanning all listed channels, OP means PTT is set to ONEPUSH, the Light icon means the manual Backlight control is activated, and you see the battery percentage.

[!NOTE] About RxMode, MO means MAIN ONLY, DW means MAIN TX / DUAL RX, DWR means DUAL RX RESPOND, and XB means CROSS BAND.

Battery display, type, and calibration

The firmware separates three different battery-related things:

For battery information on screen:

For battery percentage to make sense, two hidden-menu items matter:

Important difference:

Current BatTyp choices are:

As with any voltage-based estimate, the battery percentage is only approximate. It depends on the selected battery profile, the battery condition, and the current load.

Calibrate the battery voltage with a multimeter

  1. Make sure the radio is not charging through USB-C.
  2. Let the radio stay idle for a moment. Do not calibrate while transmitting.
  3. Measure the battery voltage with a multimeter on the battery contacts at the back of the radio / battery pack.
  4. Open the hidden menu and go to BatCal.
  5. Adjust BatCal until the voltage shown by the radio matches the multimeter as closely as possible.
  6. Confirm with M.

[!TIP] If the voltage is correct but the percentage still feels wrong, BatCal is probably fine and BatTyp is the setting to review.

About the F Lock and TXLock menus

In the past, there were a few band plans in the F Lock menu to meet various requests: PMR 446, FRS/GMRS/MURS, etc. However, adding new F Lock options always took up a lot of memory: new options in the F Lock menu, storing frequencies (for specialists, these are uint32_t each time, so they are very memory-consuming), etc.

Now, it must be recognized that it was complicated, if not impossible, to offer band plans that could cover and meet all expectations. There are too many variations from one country to another. Additionally, nothing is planned for combining multiple frequency plans from the F Lock menu. For example, opening both the PMR 446 and LPD bands. In summary, F Lock is too limited and not scalable.

Here is the solution:

  1. Select the most suitable band plan from the F Lock menu. For example, if you have a callsign and live in Europe, select CE HAM. If you do not have a callsign and are just an SWL, select DISABLE ALL, which is safer.
  2. If you still want to transmit on a memory channel that is not open by the band plan, go to the TXLock menu and choose OFF. This creates an exception and allows transmission on that channel.

In a nutshell:

If a memory channel or VFO is outside the selected band plan and TXLock is ON, there will be a small padlock to the left of the name.

For the research-oriented UNLOCK ALL procedure, see Advanced features.

Screen saver and backlight timeout

Builds with screen-saver support add the SetSav menu.

SetSav works together with BLTime: when the radio is idle and the backlight timeout expires, the screen saver can replace the normal screen instead of simply leaving the display unchanged.

Available modes are:

The logo modes use the same 128x64 logo uploaded with UV Studio.

The screen saver is intentionally suspended during active radio work: RX, TX, PTT, BEAM, and active FM scanning. It can display on the main radio screen and FM broadcast screen when the radio is idle. Pressing a key wakes the normal screen.

If BLTime is set to an always-off or always-on style value instead of a timed duration, SetSav does not take over the display.

About the SetOff menu

The SetOff menu allows you to configure a timeout before your radio enters sleep mode. This delay can be set between 1 minute and 2 hours. If SetOff is OFF, sleep mode is disabled.

For example, if you set the delay to 5 minutes and during this time there is:

then your radio will automatically enter sleep mode. You will be notified 10 seconds before with a blinking screen.

Note that sleep mode will be activated even if you are scanning, as long as no reception occurs.

FoxHunt and Beacon are deliberate exceptions: while either application is active, the radio ignores SetOff until you explicitly leave it. The normal backlight timeout still operates. See FoxHunt and Beacon.

Once in sleep mode:

To exit sleep mode, you simply need to:

As an example, I tested sleep mode on two K5(8) radios with calibrated and fully charged batteries, using the same settings, frequencies, mode (DWR), and BatSav set to 1:5. The only difference was that one radio had sleep mode enabled while the other did not. After 36 hours of operation, the radio without sleep mode had only 20% battery remaining, while the one with sleep mode still had 60% battery.

1750 Hz tone burst for repeater access

When PTT is pressed, the 1750 Hz tone can be activated by pressing Side button 2️⃣.